Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles Blog Blogs
  • Toy Jeep's Avatar
    Today, 02:29 PM
    Toy Jeep replied to a thread exhaust question in Technical Forum
    On my TJ there were 3 cats on after the Y-pipe it has being removed but the 2 up by the top of the manifold are still in place. with the third cat...
    1 replies | 8 view(s)
  • jboth's Avatar
    Today, 06:47 AM
    jboth started a thread exhaust question in Technical Forum
    i received a quote from an exhaust shop to replace both cats for $1100 or they said they could straight pipe it for $360. is this legal? if so has...
    1 replies | 8 view(s)
  • Toy Jeep's Avatar
    Yesterday, 02:45 PM
    Toy Jeep replied to a thread CJ7 Re-build V2 in Build Threads
    DamnCJ I have being following your build with interest.It has being very interesting and informative. I'm sure that Repete's build will be very...
    144 replies | 16528 view(s)
  • Iron Mike's Avatar
    05-17-2019, 07:25 PM
    Iron Mike replied to a thread CJ7 Re-build V2 in Build Threads
    This has been an interesting build and you have done a fantastic job of keeping your build moving and ever improving, and one day I may even see it...
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-14-2019, 02:32 PM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    And thanks for the kind of words about my Damn CJ...... Sent from my Pixel 2 using Tapatalk
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-14-2019, 02:32 PM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    I'll watch with interest! You should post your parts list just in case the CJ owners are purging or selling any "stock". Sent from my Pixel 2...
    144 replies | 16528 view(s)
  • Repete's Avatar
    05-13-2019, 05:45 PM
    Repete replied to a thread CJ7 Re-build V2 in Build Threads
    This has been interesting to watch. In the next few months I hope to start my work on my 85 CJ7 - just compiling parts now and looking to sell some...
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-12-2019, 04:14 PM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    VROOOM!!!! Sent from my Pixel 2 using Tapatalk
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-12-2019, 09:50 AM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    By the way, for tool transport check out my new socket roll..... Sent from my Pixel 2 using Tapatalk
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-12-2019, 09:47 AM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    Got smart near the half way point and pulled out the brass wire brushes, my nifty tight access battery drill, three batteries, and presto! Sent...
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-12-2019, 09:44 AM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    If I was going to do it again I would want access to an air compressor so I could use a cookie grinder to cut through the old baked on gasket. Using...
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-12-2019, 09:00 AM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    Out of order photo shows the gasket blow out. Sent from my Pixel 2 using Tapatalk
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-12-2019, 08:58 AM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    Getting closer. Sent from my Pixel 2 using Tapatalk
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-12-2019, 08:52 AM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    Fit in place... Sent from my Pixel 2 using Tapatalk
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-12-2019, 08:50 AM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    The part is 1/4" thick. Needed some cleanup. One would need some additional material removal to bring the undercut into the bolt hole. I picked...
    144 replies | 16528 view(s)
  • DamnCj's Avatar
    05-12-2019, 08:42 AM
    DamnCj replied to a thread CJ7 Re-build V2 in Build Threads
    Header and manifold installation on the IL6 258. Turned out to be a bit of a challenge to get them both to seal up against the gaskets. The manifold...
    144 replies | 16528 view(s)
No More Results

Powered by vBulletin® Version 4.2.3
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.
Powered by vBulletin® Version 4.2.3
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.